At present, the development of environmental protection industry continues to improve the requirements for environmental protection. The important reason is that the current environmental pollution is too serious. The use of dust removal equipment has greatly alleviated the current environmental pollution pressure, and the pollutants emitted by industrial production have reached the standard. In China, the vacuum cleaner equipment industry is an important sub-industry of the environmental protection industry.
How should the DTH drilling rig be maintained after use? Maintenance and lubrication of the rig: At the end of each shift, dirt must be removed from the machine's surface. Do not hang the filter cloth too loosely or too tightly, if it is too loose, it is easy to collect dust, and it is too tight and easy to collect dust. Reacts with water. Reacts in contact with acids, alkalis or organic solvent vapors. hardening and shrinkage caused by abnormally high temperatures; The main reasons for the aging of boiler dust collectors are as follows: The cause needs to be investigated, and measures need to be taken to eliminate and replace the filter bag. Fuel injectors regularly to ensure good lubrication of control valves, air motors and impactors. It is strictly forbidden to disassemble and disassemble parts on the working face (except when the parts are easy to handle) to avoid losing another part and damaging critical parts of another part.
At present, the development of environmental protection industry continues to improve the requirements for environmental protection. The important reason is that the current environmental pollution is too serious. The use of dust removal equipment has greatly alleviated the current environmental pollution pressure, and the pollutants emitted by industrial production have reached the standard. In China, the vacuum cleaner equipment industry is an important sub-industry of the environmental protection industry. The key to the development and growth of the environmental protection industry is to rely on the support of the vacuum cleaner equipment industry and the environmental protection service industry. According to the application category of vacuum cleaner equipment, vacuum cleaner equipment includes wastewater treatment equipment, waste management and recycling equipment, air pollution control equipment, noise elimination equipment, monitoring instruments and equipment, scientific research and laboratory equipment, including equipment for nature protection and improvement of urban environmental quality.
![DTH drilling truck - Hunan Ruisheng electromechanical equipment](/Upload/1522295469(2).jpg)
Under normal flue gas temperature conditions, only the dust collector needs to withstand temperatures below 150°C. In these occasions, chemical fibers such as polyester, polypropylene, acrylic, nylon, etc. Basically, it is usable. For occasions with high flue gas temperature, it is necessary to choose high-temperature resistant filter materials, such as glass fiber dust bags, Flumax dust bags, Mida dust bags, polyphenylene sulfide dust bags, etc. Special functional characteristics of vacuum cleaners: such as high temperature resistance, corrosion resistance, electrostatic characteristics, hydrophobicity, etc. Dust filtration characteristics: such as resistance coefficient, static dust removal capacity, dynamic dust removal capacity, filter material dynamic resistance, regeneration resistance coefficient and dust removal speed.
Before entering the site, the downhole rig must level the site and prepare slides, tools, etc. Once the rig has entered the site, it is necessary to pry the rig, lift the tires off the ground and adjust the frame to a horizontal position: when the power is turned on, the motor lifting mast can be started. After the mast is raised, the screws at the bottom of the mast are screwed out and supported on the bracket. Then install the tie rod, outrigger and pull cord, and adjust the tension of the tie rod and pull rope with a screw adjuster. The wire rope of the drilling drum of the downhole drilling rig is led out of the drum, passes through the guide pulley and tension pulley of the impact beam, and then enters the drilling pulley at the top of the mast to hang down, and the end of the wire rope is connected to the drilling rig. The rope of the mud drum is suspended downwards by a mud rope pulley at the top of the mast to connect the end with the mud shaft drum. Due to the reduction of the blowing frequency, the filtration effect of the ash layer of the filter bag can be fully exerted, thereby improving the overall dust removal efficiency. When using a 500g/m2 needle felt filter bag, the emission concentration is generally less than 20mg/Nm3.
For more information about
DTH drilling rig, pay attention to our Hunan Ruisheng Electromechanical Equipment Co., Ltd., our official website is
www.hnzega.com.