At the construction site, the washing facilities for entering and exiting vehicles were improved to ensure that vehicles leaving the house were cleaned. Automatic vehicle flushing devices should be installed at the entrances and exits of the new construction site. Water tanks should be installed on the site roads and equipped with high-pressure water guns. The construction unit shall arrange special personnel to be responsible for cleaning the entry and exit of the vehicle and the cleaning of the surrounding road surface to ensure that the vehicle is not less than 3 minutes, cleaning, the wheels and body of the car walk on the road without mud; Responsible for the "three bags in front of the door", regularly clean the mud around the cleaning device and sedimentation tank, and clean the perimeter of the gate in time to ensure that the road surface of the vehicle exit is smooth. No visible mud marks or scattered sandstone

　　The flat car wash table is divided into two parts, one part is the basis for the use of the pavement, there is no hardened pavement, and the manufacturer provides drawings to install the basic equipment parallel to the pavement.

　　One is the non-foundation type for hardening the pavement of the construction site, this non-foundation type does not need to be used as a drainage ditch, only need to make a sedimentation tank next to it can be used, which is convenient for transferring the installation speed.

　　136 nozzles can carry out all-round cleaning of the chassis and tires of construction vehicles, without dead angles, so that construction vehicles are kept clean and meet road requirements.
　　In order to meet the needs of different users, the turbine washer has two different starting methods: manual and infrared automatic sensing. The circulating water system is used for the reuse and further cleaning of wastewater. Only a small amount of water is needed in between, so a lot of water can be saved. At the same time, the company adopts high-power water pumps to make the spraying efficiency higher. Fruits meet environmental requirements.

　　 wheel washer is suitable for dust pollution enterprises such as construction sites, coal yards, brick factories, cement plants and so on.

　　Wheel washers (car gaskets, car gaskets) Correct operating procedures:

　　Wheel washer operators must be trained and familiar with the operating procedures prior to operation.

　　2. Before turning on and sending power, the wheel washer must ensure that the sensor and foot switch are normal and reset. The water level of the water tank is within the range of the car that can be washed, and there are no idle personnel in the car wash range.

　　3. Turn off the main power circuit breaker, the power indicator is on, and the wheel washer is in standby state.

　　4. Before entering the wheel washer, the cleaning steps should be informed to the driver. Slow-moving vehicles should not collide quickly and doors and windows should be closed.

　　5. During the car washing process, the power supply shall not be cut off without authorization to ensure the orderly operation of the whole process of car washing.

　　6. Clean the sludge in the sedimentation tank regularly to avoid blocking the nozzle due to mixed flow into the clear water pool.

　　7. The cleaning and maintenance of the equipment should be done during the operation interval, and the nozzle blockage should be checked regularly to avoid affecting the cleaning effect.

　　8. In any cleaning and maintenance, the power should be cut off first.

　　9. It is strictly forbidden to wash the car without water to avoid burning the water pump.

　　10. In cold weather in winter, the water in the pipe should be released after work to prevent frost damage.

　　Describe the advantages of engineering wheel washers

　　The on-site car wash machine uses intelligent control and water circulation to clean the vehicle's twin-axle tires and sides. Manual/automatic sprinkler system is adopted to meet the needs of customers, and circulating water is used to clean the vehicle to maximize water conservation. Controlling dust, controlling pollution, and reducing smog are the goals of this machine.

　　At present, it is a better environmental protection equipment. It will play a huge role in protecting the atmospheric environment from pollution. The car wash machine at this construction site will purify the atmospheric environment, reduce the appearance of pollution, reproduce the natural scenery of our blue sky and white clouds, and keep us away from pollution and health care. This machine specializes in air pollution control, adopts scientific pollution control measures, effectively controls the development trend of pollution, and plays an important role in protecting our living environment.